The RTS01 Remote Transmit Selector Panel adds capabilities and functions to any existing analog audio system to offer operators the benefits of remote transmit section (RTS), RX Activity Indication, and audio system expansion. Installation is designed to be simple with little to no impact on existing audio system wiring. The use of an external toggle switch allows pilots and operators to select a transceiver without the need to reach for the audio panel during busy flight operations so that full attention remains on critical aircraft controls and operations.
The RX Active feature allows pilots and operators to monitor which transceiver is currently active so that they can determine which radio they are actually listening to at any one time; the RX annunciator illuminates to show which transceiver is currently active regardless of which audio input is selected. The RTS expansion capability allows additional transceivers to be added to the communications system without having to remove and replace the entire audio system. Snap-in legends provide the ability to customize the label on each transceiver channel.Snap-in legends are required for operation but not included with the RST01 unit.
This RTS01 Remote Transmit Selector Panel (RTS01-001N) includes NVIS lighting.
Snap-in legendsnot includedmust be ordered separately.
7 legends required per unit, use part numbers 155-06-xxxx
友情提醒：件号：RTS01-001N 相关介绍完善中 / 部分技术参数正在核实，当前信息仅供参考，最终订货请以实际件号、原厂资料及 IPC 手册为准。
规格：
Weight:
0.8 lb
Dimensions (maximum):
0.75 x 5.00 x 5.75 in (19.05 x 127.0 x 146.1 mm)
Dimensions (behind the panel):
0.75 x 4.56 x 5.00 in (19.05 x 115.8 x 127.0 mm)
Mounting:
standard Dzus mounting (four fasteners)
Faceplate:
Lexan polycarbonate
Connectors:
1 x 44 pin D-sub plug (male)
1 x 44 pin D-sub socket (female)
V5 locking hardware
Materials/finish:
chassis and cover are brushed aluminum with chromate conversion
Temperature:
-40°C to 70°C operating
-55°C to 85°C survival
Altitude:
35,000 ft max.
Humidity:
95% at 50°C for 48 hrs
Shock:
6g for 11 ms
Electrical:
Input Operating Voltage:
28 VDC nominal
30.3 VDC maximum
22 VDC minimum
18 VDC emergency
Input Power Requirements:
400 mA max @ 28 VDC nominal
1.0 mA max @ 5 VDC; 1.0 mA max @ 28 VDC max
Input signals:
Microphone Audio (MIC Outputs from Audio Controller):
quantity; 7
circuit type; feedthrough/passive
rated level; 250 mVrms
RMT Microphone Audio:
quantity; 1
circuit type; single ended
rated level; 250 Vrms
Impedance; 150Ω ±10% (fixed, AC impedance), 480Ω ±10% (fixed, DC impedance)
MIC Bias; 12V DC (unloaded)
Transceiver Receiver Audio:
quantity; 7
circuity type; single ended
rated level; 7 Vrms max
impedance; 9.4kΩ ±10%
Transmit Keylines (from audio controller):
quantity; 7
RMT Transmit Keylines (RMT TX keyline from audio controller):
quantity; 7
rated level; active Lo (≤11.5 VDC)
Remote Transmit Selection:
quantity; 2 (RMT UP, RMT DN)
rated level; active Lo (≤11.5 VDC)
NVG Mode:
quantity; 1
rated level; active Lo (≤ 11.5 VDC)
Output Signals:
Microphone Audio (MIC Outputs to Transceivers):
quantity; 7
circuit type; single ended
rated level; 250 VRMS nominal into 150Ω
frequency response; <3 dB from 300 Hz to 6 kHz
distortion; <10% at rated output, <3% at 10% of rated power output
audio noise level; without signal >60 dB below rated output
Transceiver Receiver Audio (COM RX to Audio Controller):
quantity; 7
circuit type; feedthrough/passive
rated level; 7.00 VRMS into 1 kΩ
RMT Transceiver Receiver Audio (RMT COM RX to Audio Controller):
quantity; 1
circuit type; single ended
rated level; 7.00 VRMS into 1 kΩ
frequency response; < 10% at rated output, < 3% at 10% of rated power output
audio noise level; without signal >60 dB below rated output
Transmit Keylines (to Transceivers):
quantity; 7
circuit type; open drain
rated level; active < 100Ω to power ground, inactive > 1 MΩ to power ground
特征：
An external toggle switch connected to the flight controls provides hands-free selection of transceiver channels
RX ACTIVE detection feature illuminates a RX annunciator to indicate which transceiver is currently receiving audio signal
The RTS01 maybe incorporated as expansion panel with support for up to 7 transceivers
A wrap-around feature can be enabled or disabled for incrementing and decrementing transceiver selection when using an external toggle switch
An RX ONLY feature allows received audio for com 5, 6, and 7 to be individually monitored regardless of which transceiver is selected
Snap-in legends are used in the front panel to allow customizable labeling for radio positions; legends are required to operate the RTS01 but are not included
Night vision goggle (NVG) mode available on some models; available with NVIS Green A backlighting and NVIS Green B annunciators
